网络管理

1. 网卡命名

1.1 传统网卡命名机制

传统命名:
以太网eth[0,1,2,…]
wlan[0,1,2,…]

1.2 redhat7网卡命名机制

systemd对网络设备的命名方式:

  1. 如果Firmware或BIOS为主板上集成的设备提供的索引信息可用,且可预测,则根据此索引进行命名,例如eno1
  2. 如果Firmware或BIOS为PCI-E扩展槽所提供的索引信息可用,且可预测,则根据此索引进行命名,例如ens1
  3. 如果硬件接口的物理位置信息可用,则根据此信息进行命名,例如enp2s0
  4. 如果用户显式启动,也可根据MAC地址进行命名,例如enx2387a1dc56
  5. 上述均不可用时,则使用传统命名机制

上述命名机制中,有的需要biosdevname程序的参与。所以必须安装biosdevname程序且启用它。

1.3 网络接口名称组成格式

基于固件、设备结构、设备类型

  • 由两个字母开头标示固件
    • 以太网网卡以 en 开头
    • 无线网卡以 wl 开头
  • 设备结构
    • o:主板上集成的设备的设备索引号
    • s:扩展槽的索引号
    • x:基于MAC地址的命名
    • ps:基于物理位置拓扑的命名。如enp2s1,表示PCI总线上第2个总线的第1个插槽的设备索引号

1.4 回归传统命名

//修改网卡配置文件 [root@localhost ~]# cd /etc/sysconfig/network-scripts/ [root@localhost network-scripts]# mv ifcfg-ens33 ifcfg-eth0 [root@localhost network-scripts]# vim ifcfg-eth0 TYPE=Ethernet BOOTPROTO=dhcp DEFROUTE=yes IPV4_FAILURE_FATAL=no NAME=eth0 //此处要把ens33改成eht0 UUID=03be31f5-a3c1-4f8d-88b3-aea6e85c869f DEVICE=eth0 //此处要把ens33改成eth0 ONBOOT=yes //编辑/etc/default/grub配置文件,在以GRUB_CMDLINE_LINUX开头的行内rhgb的前面加上net.ifnames=0 biosdevname=0 [root@localhost ~]# vim /etc/default/grub GRUB_TIMEOUT=5 GRUB_DISTRIBUTOR="$(sed 's, release .*$,,g' /etc/system-release)" GRUB_DEFAULT=saved GRUB_DISABLE_SUBMENU=true GRUB_TERMINAL_OUTPUT="console" GRUB_CMDLINE_LINUX="crashkernel=auto rd.lvm.lv=rhel/root rd.lvm.lv=rhel/swap net.ifnames=0 biosdevname=0 rhgb quiet" GRUB_DISABLE_RECOVERY="true" //为grub2生成其配置文件 [root@localhost ~]# grub2-mkconfig -o /etc/grub2.cfg Generating grub configuration file ... Found linux image: /boot/vmlinuz-3.10.0-693.el7.x86_64 Found initrd image: /boot/initramfs-3.10.0-693.el7.x86_64.img Found linux image: /boot/vmlinuz-0-rescue-fd0bcf5782d24ba5b903b175c35f328e Found initrd image: /boot/initramfs-0-rescue-fd0bcf5782d24ba5b903b175c35f328e.img done //重启系统 [root@localhost ~]# reboot

2. 网络管理常用命令

2.1 ifconfig

//查看当前处于活动状态的所有网络接口 [root@localhost ~]# ifconfig eth0: flags=4163 mtu 1500 inet 172.16.12.128 netmask 255.255.255.0 broadcast 172.16.12.255 inet6 fe80::20c:29ff:fe73:110 prefixlen 64 scopeid 0x20 ether 00:0c:29:73:01:10 txqueuelen 1000 (Ethernet) RX packets 5121 bytes 424364 (414.4 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 3813 bytes 3257482 (3.1 MiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 lo: flags=73 mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 inet6 ::1 prefixlen 128 scopeid 0x10 loop txqueuelen 1 (Local Loopback) RX packets 4 bytes 344 (344.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 4 bytes 344 (344.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 //仅查看eth0网卡状态 [root@localhost ~]# ifconfig eth0 eth0: flags=4163 mtu 1500 inet 172.16.12.128 netmask 255.255.255.0 broadcast 172.16.12.255 inet6 fe80::20c:29ff:fe73:110 prefixlen 64 scopeid 0x20 ether 00:0c:29:73:01:10 txqueuelen 1000 (Ethernet) RX packets 5148 bytes 426572 (416.5 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 3828 bytes 3259946 (3.1 MiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 //查看所有网卡状态信息, 包括禁用和启用 [root@localhost ~]# ifconfig -a eth0: flags=4163 mtu 1500 inet 172.16.12.128 netmask 255.255.255.0 broadcast 172.16.12.255 inet6 fe80::20c:29ff:fe73:110 prefixlen 64 scopeid 0x20 ether 00:0c:29:73:01:10 txqueuelen 1000 (Ethernet) RX packets 5177 bytes 428948 (418.8 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 3844 bytes 3262104 (3.1 MiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 lo: flags=73 mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 inet6 ::1 prefixlen 128 scopeid 0x10 loop txqueuelen 1 (Local Loopback) RX packets 4 bytes 344 (344.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 4 bytes 344 (344.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 //网卡配置信息含义如下: UP: 网卡处于活动状态 BROADCAST: 支持广播 RUNNING: 网线已接入 MULTICAST: 支持组播 MTU: 最大传输单元(字节),即此接口一次所能传输的最大封包 inet: 显示IPv4地址行 inet6: 显示IPv6地址行 link/enther: 指设备硬件(MAC)地址 txqueuelen: 传输缓存区长度大小 RX packets: 接收的数据包 TX packets: 发送的数据包 errors: 总的收包的错误数量 dropped: 由于各种原因, 导致拷贝在内存过程中被丢弃 collisions: 网络信号冲突情况, 值不为0则可能存在网络故障

2.2 ip

//语法:ip [ OPTIONS ] OBJECT { COMMAND | help } OBJECT: link:网络接口属性 addr:协议地址 route:路由 //查看网络接口所有地址 [root@localhost ~]# ip link show 1: lo: mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT qlen 1 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 2: eth0: mtu 1500 qdisc pfifo_fast state UP mode DEFAULT qlen 1000 link/ether 00:0c:29:73:01:10 brd ff:ff:ff:ff:ff:ff //显示报文统计信息 [root@localhost ~]# ip -s link show 1: lo: mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT qlen 1 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 RX: bytes packets errors dropped overrun mcast 0 0 0 0 0 0 TX: bytes packets errors dropped carrier collsns 0 0 0 0 0 0 2: eth0: mtu 1500 qdisc pfifo_fast state UP mode DEFAULT qlen 1000 link/ether 00:0c:29:73:01:10 brd ff:ff:ff:ff:ff:ff RX: bytes packets errors dropped overrun mcast 23826 255 0 0 0 0 TX: bytes packets errors dropped carrier collsns 21275 157 0 0 0 0 //启用或禁用网络接口ip link set DEV {up|down} [root@localhost ~]# ip link set lo down [root@localhost ~]# ip link set lo up //ip addr add ADDRESS dev DEV:添加IP地址 [root@localhost ~]# ip addr show eth0 2: eth0: mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:0c:29:73:01:10 brd ff:ff:ff:ff:ff:ff inet 172.16.12.128/24 brd 172.16.12.255 scope global dynamic eth0 valid_lft 1683sec preferred_lft 1683sec inet6 fe80::20c:29ff:fe73:110/64 scope link valid_lft forever preferred_lft forever [root@localhost ~]# ip addr add 192.168.1.1/24 dev eth0 [root@localhost ~]# ip addr show eth0 2: eth0: mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:0c:29:73:01:10 brd ff:ff:ff:ff:ff:ff inet 172.16.12.128/24 brd 172.16.12.255 scope global dynamic eth0 valid_lft 1657sec preferred_lft 1657sec inet 192.168.1.1/24 scope global eth0 valid_lft forever preferred_lft forever inet6 fe80::20c:29ff:fe73:110/64 scope link valid_lft forever preferred_lft forever //ip addr del ADDRESS dev DEV:删除IP地址 [root@localhost ~]# ip addr show eth0 2: eth0: mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:0c:29:73:01:10 brd ff:ff:ff:ff:ff:ff inet 172.16.12.128/24 brd 172.16.12.255 scope global dynamic eth0 valid_lft 1603sec preferred_lft 1603sec inet 192.168.1.1/24 scope global eth0 valid_lft forever preferred_lft forever inet6 fe80::20c:29ff:fe73:110/64 scope link valid_lft forever preferred_lft forever [root@localhost ~]# ip addr del 192.168.1.1/24 dev eth0 [root@localhost ~]# ip addr show eth0 2: eth0: mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:0c:29:73:01:10 brd ff:ff:ff:ff:ff:ff inet 172.16.12.128/24 brd 172.16.12.255 scope global dynamic eth0 valid_lft 1580sec preferred_lft 1580sec inet6 fe80::20c:29ff:fe73:110/64 scope link valid_lft forever preferred_lft forever //ip addr show DEV:查看网络接口的地址 [root@localhost ~]# ip addr show eth0 2: eth0: mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:0c:29:73:01:10 brd ff:ff:ff:ff:ff:ff inet 172.16.12.128/24 brd 172.16.12.255 scope global dynamic eth0 valid_lft 1580sec preferred_lft 1580sec inet6 fe80::20c:29ff:fe73:110/64 scope link valid_lft forever preferred_lft forever

2.3 route

Linux主机之间是使用IP进行通信, 假设A主机和B主机同在一个网段内且网卡都处于激活状态, 则A具备和B直接通信的能力, 但如果A主机和B主机处于两个不同的网段, 则A必须通过路由器才能和B通信, 路由器属于IT设备的基础设施, 每一个网段都应该至少有一个网关

//查看当前路由表 [root@localhost ~]# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default gateway 0.0.0.0 UG 100 0 0 ens33 172.16.12.0 0.0.0.0 255.255.255.0 U 100 0 0 ens33 //以数字方式显示各主机或端口等相关信息 [root@localhost ~]# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 172.16.12.2 0.0.0.0 UG 100 0 0 ens33 172.16.12.0 0.0.0.0 255.255.255.0 U 100 0 0 ens33 //增加路由 //语法:route add [-net|-host] target [netmask Nm] [gw Gw] [[dev] If] //增加网段路由 [root@localhost ~]# route add -net 172.16.12.0/24 gw 172.16.12.2 dev eth1 [root@localhost ~]# route add -net 0.0.0.0/0 gw 172.16.12.2 dev eth1 //增加主机路由 [root@localhost ~]# route add -host 172.16.12.128 gw 172.16.12.2 //删除路由 [root@localhost ~]# route del -net 172.16.12.0/24 [root@localhost ~]# route del -net 0.0.0.0/0 gw 172.16.12.2

2.4 hostname与hostnamectl

生产环境中必须配置主机名,同时主机名也需要遵循一定的规范, 比如:

公有云: 地区-项目-业务-服务-节点-地址 wh-shop-register-nginx-node1-192.168.56.13 wh-med-pay-mysql-master01-192.168.56.11 wh-med-pay-mysql-slave01-192.168.56.12 //hostname查看主机名 [root@localhost ~]# hostname localhost.localdomain //hostname临时修改主机名 [root@localhost ~]# hostname wangqing [root@localhost ~]# cat /etc/hostname localhost.localdomain //注意:修改主机名后需要重新登录用户才会显示效果 //rhel7系统建议使用hostnamectl修改和查看主机名 //设定永久名称 [root@localhost ~]# hostnamectl set-hostname seancheng [root@localhost ~]# cat /etc/hostname seancheng //查看主机信息 [root@localhost ~]# hostnamectl Static hostname: seancheng Icon name: computer-vm Chassis: vm Machine ID: fd0bcf5782d24ba5b903b175c35f328e Boot ID: a060e3a2882f4d2c92884eee9db702bc Virtualization: vmware Operating System: Red Hat Enterprise Linux Server 7.4 (Maipo) CPE OS Name: cpe:/o:redhat:enterprise_linux:7.4:GA:server Kernel: Linux 3.10.0-693.el7.x86_64 Architecture: x86-64

注意:
在Linux中以命令方式修改网络配置只在当前状态有效,重启后将失效。故若想使修改的配置重启后依然有效,则必须编辑配置文件进行配置的修改。

3. 网络相关配置文件

3.1 网络配置文件

//网络配置文件:/etc/sysconfig/network NETWORKING={yes|no}:设定整个系统是否启用网络功能,若设为no,则不论网卡如何设置都不能使用网络功能。 HOSTNAME:设置主机名

3.2 网络接口配置文件

网络接口即网卡,其配置文件的路径是/etc/sysconfig/network-scripts/ifcfg-INTERFACE_NAME

[root@localhost ~]# vi /etc/sysconfig/network-scripts/ifcfg-eth1 TYPE=Ethernet BOOTPROTO=static NAME=eth1 UUID=03be31f5-a3c1-4f8d-88b3-aea6e85c869f DEVICE=eth1 ONBOOT=yes IPADDR=172.16.12.130 NETMASK=255.255.255.0 GATEWAY=172.16.12.2 DNS1=172.16.12.2 //网卡配置说明 //参数 说明 BOOTPROTO=none //引导协议,可选值有{static|none|dhcp|bootp}。如果要使用静态地址,使用static或none都可以 NM_CONTROLLED //NM是NetworkManager的简写,NM是由RHEL研发的在RHEL6中取代network脚本来实现网络管理、配置的服务脚本 //可选值有{ yes | no } //此项是设定此网卡是否接受NM控制。CentOS6建议设为“no” TYPE //接口类型。常见的接口类型有:Ethernet,Bridge UUID //设备的惟一标识 HWADDR //硬件地址,要与硬件中的地址保持一致,可省 IPADDR=172.16.12.130 //固定IP地址 PREFIX=24 //子网掩码 NETMASK=255.255.255.0 //子网掩码 GATEWAY=172.16.12.2 //默认网关 DNS1=172.16.12.2 //第一个DNS服务器指向 DNS2 //第二个DNS服务器指向 DNS3 //第三个DNS服务器指向 DEVICE=eth1 //关联的设备名称,要与文件名的后半部"INTERFACE_NAME"保持一致 NAME="eth1" //连接名称 ONBOOT=yes //在系统引导时是否自动激活此网络接口,可选值有{ yes | no } DEFROUTE=yes //将接口设定为默认路由[yes|no] USERCTL={yes|no} //是否允许普通用户控制此接口的启用与禁用 PEERDNS={yes|no} //是否在BOOTPROTO为dhcp时接受由dhcp服务器指定的DNS地址,此项设为yes时获得的DNS地址将直接覆盖至/etc/resolv.conf文件中

3.3 路由配置文件

路由配置文件的路径是/etc/sysconfig/network-scripts/route-INTERFACE_NAME

//添加格式一:DEST via NEXTHOP [root@localhost ~]# vi /etc/sysconfig/network-scripts/route-ens33 172.16.12.0/24 via 172.16.12.2 //添加格式二: [root@localhost ~]# vi /etc/sysconfig/network-scripts/route-ens33 ADDRESS0=172.16.12.0 NETMASK0=255.255.255.0 GATEWAY0=172.16.12.2

3.4 DNS配置文件

DNS配置文件的路径是/etc/resolv.conf

[root@localhost ~]# vi /etc/resolv.conf nameserver DNS_IP_1 nameserver DNS_IP_2 nameserver DNS_IP_3

4. NetworkManager管理网络

  1. RHEL/CentOS7`系统默认使用`NetworkManager`来提供网络服务,这是一种动态管理网络配置的守护进程,能够让网络设备保持连接状态。
  2. `NetworkManager`提供的命令行和图形配置工具对网络进行设定, 设定保存的配置文件在`/etc/sysconfig/network-scripts`目录下, 工具有 `nmcli, nmtui, nm-connection-editor

device物理设备, 例如 ens33,enp2s0,virbr0,team0
connection连接设置, 具体网络配置方案

1.不同的网络连接配置可以应用到相同的物理设备,但物理设备同一时间只能应用其中某个网络连接
2.针对物理网络接口, 设定不同的网络连接, 在不同的使用环境中激活相应的网络连接,就可以实现网络配置信息的自动切换了

使用nmcli命令查看设备以及连接情况

//查看设备状态 [root@localhost ~]# nmcli device DEVICE TYPE STATE CONNECTION ens33 ethernet connected ens33 lo loopback unmanaged -- //查看指定设备的详细状态 [root@localhost ~]# nmcli device show ens33 GENERAL.DEVICE: ens33 GENERAL.TYPE: ethernet GENERAL.HWADDR: 00:0C:29:73:01:10 GENERAL.MTU: 1500 GENERAL.STATE: 100 (connected) GENERAL.CONNECTION: ens33 GENERAL.CON-PATH: /org/freedesktop/NetworkManager/ActiveConnection/1 WIRED-PROPERTIES.CARRIER: on IP4.ADDRESS[1]: 172.16.12.128/24 IP4.GATEWAY: 172.16.12.2 IP4.DNS[1]: 172.16.12.2 IP4.DOMAIN[1]: localdomain IP6.ADDRESS[1]: fe80::20c:29ff:fe73:110/64 IP6.GATEWAY: -- //查看连接状态 [root@localhost ~]# nmcli connection NAME UUID TYPE DEVICE ens33 03be31f5-a3c1-4f8d-88b3-aea6e85c869f 802-3-ethernet ens33 //查看所有活动的连接 NAME UUID TYPE DEVICE ens33 03be31f5-a3c1-4f8d-88b3-aea6e85c869f 802-3-ethernet ens33 //查看指定设备连接的详细情况 [root@localhost ~]# nmcli connection show ens33 connection.id: ens33 connection.uuid: 03be31f5-a3c1-4f8d-88b3-aea6e85c869f connection.stable-id: -- connection.interface-name: ens33 connection.type: 802-3-ethernet connection.autoconnect: yes connection.autoconnect-priority: 0 connection.autoconnect-retries: -1 (default) connection.timestamp: 1530455962 connection.read-only: no connection.permissions: -- connection.zone: -- connection.master: -- connection.slave-type: -- connection.autoconnect-slaves: -1 (default) connection.secondaries: -- connection.gateway-ping-timeout: 0 ......

5. 使用原生network管理网络

CentOS/RHEL的网络配置文件默认目录为/etc/sysconfig/network-scripts
默认第一块物理网卡配置文件为ifcfg-eth0, 如果有第二块物理网卡, 配置文件则为ifcfg-eth1以此类推。 注意: 如果新增物理网卡没有配置文件,可选择复制系统默认的进行修改。

//设置NetworkManger开机不启动, 同时停止NetworkManger服务 [root@localhost ~]# systemctl disable NetworkManager [root@localhost ~]# systemctl stop NetworkManager //添加一块物理网卡, 然后新增网络连接配置文件 //复制配置eth0配置文件为eth1 [root@localhost ~]# cp /etc/sysconfig/network-scripts/{ifcfg-eth0,ifcfg-eth1} //编辑网卡配置文件 [root@localhost ~]# vi /etc/sysconfig/network-scripts/ifcfg-eth1 TYPE=Ethernet BOOTPROTO=static NAME=eth1 UUID=03be31f5-a3c1-4f8d-88b3-aea6e85c869f DEVICE=eth1 NM_CONTROLLED=no ONBOOT=yes IPADDR=172.16.12.130 NETMASK=255.255.255.0 GATEWAY=172.16.12.2 DNS1=172.16.12.2 //重启network网络服务加载网络并设置开机启动 [root@localhost ~]# systemctl restart network [root@localhost ~]# systemctl enable network

6. 网络检测工具与故障排查

6.1 ping

ping命令的目的在于测试另一台主机是否可达, 如果ping不到某台主机,就说明对方主机已经出现了问题, 但是不排除由于链路中的防火墙、ping被丢弃等原因造成ping不通的情况

//ping命令常用选项: -c 指定ping的次数 -i 指定ping包的发送间隔 -w 如果ping没有回应, 则在指定超时时间后退出

6.2 host与nslookup

host/nslookup命令用于查询DNS记录

[root@localhost ~]# host www.baidu.com www.baidu.com is an alias for www.a.shifen.com. www.a.shifen.com has address 119.75.216.20 www.a.shifen.com has address 119.75.213.61 [root@localhost ~]# nslookup www.baidu.com Server: 172.16.12.2 Address: 172.16.12.2#53 Non-authoritative answer: www.baidu.com canonical name = www.a.shifen.com. Name: www.a.shifen.com Address: 119.75.213.61 Name: www.a.shifen.com Address: 119.75.216.20

6.3 netstat

netstat用于查看网络状态

//显示路由表 [root@seancheng ~]# netstat -r Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface default gateway 0.0.0.0 UG 0 0 0 ens33 172.16.12.0 0.0.0.0 255.255.255.0 U 0 0 0 ens33 //以数字方式显示路由表 [root@seancheng ~]# netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 0.0.0.0 172.16.12.2 0.0.0.0 UG 0 0 0 ens33 172.16.12.0 0.0.0.0 255.255.255.0 U 0 0 0 ens33 //显示建立的tcp连接 [root@seancheng ~]# netstat -t Active Internet connections (w/o servers) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 seancheng:ssh 172.16.12.1:56187 ESTABLISHED tcp 0 0 seancheng:ssh 172.16.12.1:53808 ESTABLISHED //显示udp连接 [root@seancheng ~]# netstat -u Active Internet connections (w/o servers) Proto Recv-Q Send-Q Local Address Foreign Address State [root@seancheng ~]# //显示监听状态的连接 [root@seancheng ~]# netstat -l Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 0.0.0.0:ssh 0.0.0.0:* LISTEN tcp 0 0 localhost:smtp 0.0.0.0:* LISTEN tcp6 0 0 [::]:ssh [::]:* LISTEN tcp6 0 0 localhost:smtp [::]:* LISTEN //显示监听指定的套接字的进程的进程号及进程名 [root@seancheng ~]# netstat -p Active Internet connections (w/o servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 seancheng:ssh 172.16.12.1:56187 ESTABLISHED 2094/sshd: root@pts tcp 0 0 seancheng:ssh 172.16.12.1:53808 ESTABLISHED 1077/sshd: root@pts //显示所有状态的连接 [root@seancheng ~]# netstat -a Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 0.0.0.0:ssh 0.0.0.0:* LISTEN tcp 0 0 localhost:smtp 0.0.0.0:* LISTEN tcp 0 0 seancheng:ssh 172.16.12.1:56187 ESTABLISHED tcp 0 0 seancheng:ssh 172.16.12.1:53808 ESTABLISHED tcp6 0 0 [::]:ssh [::]:* LISTEN tcp6 0 0 localhost:smtp [::]:* LISTEN udp 0 0 0.0.0.0:23511 0.0.0.0:* udp 0 0 0.0.0.0:bootpc 0.0.0.0:* udp6 0 0 [::]:35299 [::]:* //常用选项 -antlp [root@seancheng ~]# netstat -antlp Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN 889/sshd tcp 0 0 127.0.0.1:25 0.0.0.0:* LISTEN 1007/master tcp 0 0 172.16.12.128:22 172.16.12.1:56187 ESTABLISHED 2094/sshd: root@pts tcp 0 0 172.16.12.128:22 172.16.12.1:53808 ESTABLISHED 1077/sshd: root@pts tcp6 0 0 :::22 :::* LISTEN 889/sshd tcp6 0 0 ::1:25 :::* LISTEN 1007/master

6.4 ss

ss是一种网络状态查看工具,取代netstat

//语法:ss [options] [ FILTER ] //常用的options: -t:tcp协议相关 -u:udp协议相关 -w:裸套接字相关 -x:unix套接字相关 -l:listen状态的连接 -a:所有 -n:数字格式 -p:相关的程序及pid -e:扩展的信息 -m:内存用量 -o:显示计时器信息 //常见的FILTER: FILTER := [ state TCP-STATE ] [ EXPRESSION ] 如:ss -tan state ESTABLISHED //常见的state: //tcp finite state machine:有限状态机 LISTENING:监听 ESTABLISHED:已建立的连接 //EXPRESSION: dport = sport = 示例:'( dport = :ssh or sport = :ssh)',此处的ssh也即服务名可以使用其对应的端口号代替,等号两边必须有空格 //常用组合: [root@seancheng ~]# ss -tan State Recv-Q Send-Q Local Address:Port Peer Address:Port LISTEN 0 128 *:22 *:* LISTEN 0 100 127.0.0.1:25 *:* ESTAB 0 0 172.16.12.128:22 172.16.12.1:56187 ESTAB 0 0 172.16.12.128:22 172.16.12.1:53808 LISTEN 0 128 :::22 :::* LISTEN 0 100 ::1:25 :::* [root@seancheng ~]# ss -tanl State Recv-Q Send-Q Local Address:Port Peer Address:Port LISTEN 0 128 *:22 *:* LISTEN 0 100 127.0.0.1:25 *:* LISTEN 0 128 :::22 :::* LISTEN 0 100 ::1:25 :::* [root@seancheng ~]# ss -antlp State Recv-Q Send-Q Local Address:Port Peer Address:Port LISTEN 0 128 *:22 *:* users:(("sshd",pid=889,fd=3)) LISTEN 0 100 127.0.0.1:25 *:* users:(("master",pid=1007,fd=13)) LISTEN 0 128 :::22 :::* users:(("sshd",pid=889,fd=4)) LISTEN 0 100 ::1:25 :::* users:(("master",pid=1007,fd=14)) [root@seancheng ~]# ss -anu State Recv-Q Send-Q Local Address:Port Peer Address:Port UNCONN 0 0 *:23511 *:* UNCONN 0 0 *:68 *:* UNCONN 0 0 :::35299 :::* //常见端口 http 80/tcp https 443/tcp ssh 22/tcp ftp 20,21/tcp mysql 3306/tcp rsync 873/rsync redis 6379/tcp

作业

1.如何查看系统中每个ip的连接数
2.请列出下列服务使用的端口,http,ftp,ssh,telnet,mysql,dns
3.如何在虚拟机上新增加一块网卡,并配置IP为172.16.0.10,指定网关为172.16.0.1
4.详细描述dns解析过程,以访问www.baidu.com为例
5.如何查看系统中运行了多少个进程
6.如何查看系统中启动了哪些端口
7.如何查看是否开启80端口,及查看sshd进程是否存在
8.列出所有处于监听状态的tcp端口
9.查看所有的端口信息, 包括 PID 和进程名称